Features:

• Ancor NMEA 2000 power isolator can be used to isolate the power of two independent NMEA 2000 networks.
• Reduce battery power consumption by switching off one part of the network while the other remains operational. You can also use this to solve voltage drop problems in long networks.
• Yellow connector blocks connect to trunk cables and T-connectors, creating a simplified, colour-coded network installation.
• Colour-coded simple installation and component identification
• Compatible with all NMEA 2000 Micro-C devices and accessories.

Note:

Use original adapter cables to integrate the NMEA2000 network with the Raymarine STNG network. Do not duplicate the power supply or ground for different integrated networks.

The post NMEA 2000 toiteisolaator appeared first on NavSystems.

ANCOR NMEA 2000 4-way connector allows the connection of four devices with drop cables between NMEA 2000 backbone cables. The yellow connectors connect to the Ancor 4T connector and backbone cables, and the black connectors connect to the drop cables, creating a simplified and clear colour-coded network installation.

Note:

Use original adapter cables to integrate the NMEA2000 network with the Raymarine STNG network. Do not duplicate the power supply or ground for different integrated networks.

The post NMEA 2000 4T-liitmik appeared first on NavSystems.

ANKOR NMEA 2000 T-piece allows two devices to be connected via drop cables between NMEA 2000 backbone cables. The yellow connectors connect to the Ancor 2T connector and backbone cables, and the black connectors connect to drop cables, creating a simplified and clearly colour-coded network installation.

Note:

Use original adapter cables to integrate the NMEA2000 network with the Raymarine STNG network. Do not duplicate the power supply or ground for different integrated networks.

The post NMEA 2000 2T-liitmik appeared first on NavSystems.

ANCOR NMEA 2000 single T-connector allows connection of a single device via drop cable between NMEA 2000 backbone cables. The yellow connectors connect to the Ancor T-connector and backbone cables, and the black connector connects to the drop cable, creating a simplified and clearly colour-coded network installation.

Note:

Use original adapter cables to integrate the NMEA2000 network with the Raymarine STNG network. Do not duplicate the power supply or ground for different integrated networks.

The post NMEA 2000 T-liitmik appeared first on NavSystems.

The Maretron NMEA 2000 Micro-C protective cap is designed to cover empty, spare connection sockets. These protective caps have no electronic significance whatsoever; they are simply blanking plugs, providing protection against water and dirt.

The post NMEA 2000 Micro Male kaitsekork (katab kinni Male pistiku) appeared first on NavSystems.

The Maretron NMEA 2000 Micro-C protective cap is designed to cover empty, spare connection sockets. These protective caps have no electronic significance whatsoever; they are simply blanking plugs, providing protection against water and dirt.

The post NMEA 2000 Micro Female kaitsekork (katab kinni Female pesa) appeared first on NavSystems.

The Maretron in-line NMEA 2000 Micro-C straight connector is designed to create straight cable terminations. The connector can be fitted to the ends of all NMEA 2000 cables taken from the reel with a diameter of 6-8 mm. The connector has screw terminals for cable connection and a connector with a Micro-C end. It is important to use only dedicated NMEA 2000® approved cables and connectors in NMEA 2000® networks to ensure correct data transmission and network reliability. Use original adapter cables to integrate your NMEA2000 network with a Raymarine STNG network. Do not duplicate the power supply circuit or earthing of different integrated networks.

Features:

• Screw terminals for cable connection
• Screw terminal for a good connection 
• Space-saving design/Male plug
• Cast housing material/Colour: Thermoplastic PUR/Black
• Contact carrier material/colour: Thermoplastic PUR/Black
• Kontaktmateriaal/kap: messing/goud
• Coupling material/coating: brass/nickel

Electric:

• Voltage rating: 250V 
• Load capacity 4 A

Environment

• Protection class: IEC IP68, NEMA 1, 3, 4, 6P

Fastenings

• NMEA: Approved by NMEA 2000®
• IEC: IEC 61162-3

Quick guide

Thread the NMEA 2000 cable through the connector housing. Strip approximately 20 mm of the cable's outer insulation. Cut the blue wire 7 mm shorter than the others. Clean the wire ends and fit uninsulated ferrules (max. length 6 mm) to all wires that will be screwed down. Fit a heat shrink tube over the unsleeved drain wire to prevent it from touching the screw for the central Can-L (blue) terminal. The blue wire, which is 7 mm shorter than the others, should be connected last. Insert the connector core into the housing so that the wire groove faces the desired direction; there are 4 possible positions. Hand-tighten the plastic nut; do not overtighten. Ensure the cable exiting the connector is free in the socket and manually tighten the cable strain relief nut.

Instructions:

Download Maretron MNEA2000 screw-in fittings information sheet.

The post Isepaigaldatav NMEA 2000 liitmik (Male) appeared first on NavSystems.

The Maretron in-line NMEA 2000 Micro-C straight connector is designed to create straight cable terminations. The connector can be fitted to the ends of all NMEA 2000 cables taken from the reel with a diameter of 6-8 mm. The connector has screw terminals for cable connection and a connector with a Micro-C end. It is important to use only dedicated NMEA 2000® approved cables and connectors in NMEA 2000® networks to ensure correct data transmission and network reliability. Use original adapter cables to integrate your NMEA2000 network with a Raymarine STNG network. Do not duplicate the power supply circuit or earthing of different integrated networks.

Features:

• Screw terminals for cable connection
• Screw terminal for a good connection 
• Space-saving design / Female connector
• Cast housing material/Colour: Thermoplastic PUR/Black
• Contact carrier material/colour: Thermoplastic PUR/Black
• Kontaktmateriaal/kap: messing/goud
• Coupling material/coating: brass/nickel

Electric:

• Voltage rating: 250V 
• Load capacity 4 A

Environment

• Protection class: IEC IP68, NEMA 1, 3, 4, 6P

Fastenings

• NMEA: Approved by NMEA 2000®
• IEC: IEC 61162-3

Quick guide

Thread the NMEA 2000 cable through the connector housing. Strip approximately 20 mm of the cable's outer insulation. Cut the blue wire 7 mm shorter than the others. Clean the wire ends and fit uninsulated ferrules (max. length 6 mm) to all wires that will be screwed down. Fit a heat shrink tube over the unsleeved drain wire to prevent it from touching the screw for the central Can-L (blue) terminal. The blue wire, which is 7 mm shorter than the others, should be connected last. Insert the connector core into the housing so that the wire groove faces the desired direction; there are 4 possible positions. Hand-tighten the plastic nut; do not overtighten. Ensure the cable exiting the connector is free in the socket and manually tighten the cable strain relief nut.

Instructions:

Download Maretron MNEA2000 screw-in fittings information sheet.

The post Isepaigaldatav NMEA 2000 liitmik (Female) appeared first on NavSystems.

The Maretron field-installable NMEA 2000 Micro-C angled connector is designed for 90º turns in tight spaces. Often, situations arise where a new device just barely fits into an old console, but straight connector cables no longer fit. This is where the 90º angled connector comes in handy. The field-installable angled connector has another useful feature: its internal components can be rotated so that the connector's pinout faces four different directions. In NMEA 2000® systems, it is crucial to use only specially approved NMEA 2000® cables and connectors to ensure correct data transmission and network reliability. To integrate an NMEA2000 network with a Raymarine STNG network, use original adapter cables. Do not duplicate the power supply or grounding of different integrated networks.

Features:

• Screw terminals for cable connection
• Screw terminal for a good connection 
• 90° corner space-saving design/male/female connector
• Cast housing material/Colour: Thermoplastic PUR/Black
• Contact carrier material/colour: Thermoplastic PUR/Black
• Kontaktmateriaal/kap: messing/goud
• Coupling material/coating: brass/nickel

Electric:

• Voltage rating: 250V 
• Load capacity 4 A

Environment

• Protection class: IEC IP68, NEMA 1, 3, 4, 6P

Fastenings

• NMEA: Approved by NMEA 2000®
• IEC: IEC 61162-3

Quick guide

Thread the NMEA 2000 cable through the connector housing. Strip approximately 20 mm of the cable's outer insulation. Cut the blue wire 7 mm shorter than the others. Clean the wire ends and fit uninsulated ferrules (max. length 6 mm) to all wires that will be screwed down. Fit a heat shrink tube over the unsleeved drain wire to prevent it from touching the screw for the central Can-L (blue) terminal. The blue wire, which is 7 mm shorter than the others, should be connected last. Insert the connector core into the housing so that the wire groove faces the desired direction; there are 4 possible positions. Hand-tighten the plastic nut; do not overtighten. Ensure the cable exiting the connector is free in the socket and manually tighten the cable strain relief nut.

Instructions:

Download Maretron MNEA2000 screw-in fittings information sheet.

The post Isepaigaldatav NMEA 2000 nurkliitmik 90º (Male) appeared first on NavSystems.

The Maretron field-installable NMEA 2000 Micro-C angled connector is designed for making 90º turns in tight spaces. Often, situations arise where a new plotter just barely fits into an old mounting console, but straight connector cables no longer fit. This is where the 90º angled connector comes in handy. The field-installable angled connector has another good feature: its insert can be rotated so that the connector's pinout faces in four different directions. In NMEA 2000® systems, it is essential to use only special NMEA 2000® approved cables and connectors to ensure correct data transmission and network reliability. Use original adapter cables to integrate the NMEA2000 network with a Raymarine STNG network. Do not duplicate the power supply or ground of different integrated networks.

Features:

• Screw terminals for cable connection
• Screw terminal for a good connection 
• 90° corner space-saving design/male/female connector
• Cast housing material/Colour: Thermoplastic PUR/Black
• Contact carrier material/colour: Thermoplastic PUR/Black
• Kontaktmateriaal/kap: messing/goud
• Coupling material/coating: brass/nickel

Electric:

• Voltage rating: 250V 
• Load capacity 4 A

Environment

• Protection class: IEC IP68, NEMA 1, 3, 4, 6P

Fastenings

• NMEA: Approved by NMEA 2000®
• IEC: IEC 61162-3

Quick guide

Thread the NMEA 2000 cable through the connector housing. Strip approximately 20 mm of the cable's outer insulation. Cut the blue wire 7 mm shorter than the others. Clean the wire ends and fit uninsulated ferrules (max. length 6 mm) to all wires that will be screwed down. Fit a heat shrink tube over the unsleeved drain wire to prevent it from touching the screw for the central Can-L (blue) terminal. The blue wire, which is 7 mm shorter than the others, should be connected last. Insert the connector core into the housing so that the wire groove faces the desired direction; there are 4 possible positions. Hand-tighten the plastic nut; do not overtighten. Ensure the cable exiting the connector is free in the socket and manually tighten the cable strain relief nut.

Instructions:

Download Maretron MNEA2000 screw-in fittings information sheet.

The post Isepaigaldatav NMEA 2000 nurkliitmik 90º (Female) appeared first on NavSystems.